Product weight: earrings (pair) - 17.9 grams pendant 19.9 grams
Materials
- silver earrings — 2 pieces;
- silver memory wire with large diameter is 1.5 revolution;
- silver memory wire with a small diameter and a 4 ? revolution;
- T — shaped silver clove (Pina) — 14 pieces;
- blue beads — 259; blue beads with iridescence — 259;
- transparent light blue beads — 150 pieces;
- flat faceted sky blue glass crystals with a diameter of 0.5 cm — 36 pieces;
- oval faceted transparent glass beads with a diameter of 1 cm — 12 pieces;
- oval faceted blue lampwork glass beads with a diameter of one cm — 1 piece;
- oval faceted blue lampwork glass beads with a diameter of 1.2 cm — 7 pieces (holes large blue beads and smaller blue beads should be wide enough for threading the two clasped each other of the segments of wire).
Job description
- Two full turns of small diameter wire manufacture components of earrings. At one end of the wire with round nose pliers make a loop inside.
- On the free end of the string five light blue beads. Next: one blue bead, one crystal, one blue bead and repeat the cycle four more times at intervals of three blue beads. Then strung: 10 light blue beads, one blue bead, one large blue bead. For a large blue bead symmetrically duplicate the alternating blue crystals and beads. At the end of the wire with round nose pliers form a loop outside and fasten it on the inner loop of the opposite end. Get the round base of the pendant. Through the large blue bead is threaded ? the circumference of the spring wire of small diameter so that two sides was equal segments.
- On the free ends of the two sides strung on: 5 light blue beads, 5 blue beads, 5 blue beads, 4 blue beads, one crystal and 3 blue beads. Wire lock internal hinges. The same pattern make the second earring.
- For the manufacture of the inner pendants earrings take the T — shaped stud and insert: one large blue bead, 5 blue beads, 5 blue beads, one blue bead, one crystal, one blue bead, 5 blue beads, 2 blue beads and a simple block earring post loop. Similarly, manufacture of the second suspension.
- From the inner loop bead rings attach charms. Open loop pendants pliers and tonkokostny as a ring. Put it on the inner loop and close. Also attach the second hanger.
- In the manufacture of short suspensions after stringing a sufficient number of beads and beads and cut the excess wire. Leave the free end of a length of 1.2 cm and lock carnations are simple loops.
- For the manufacture of the lower suspension earrings take the T — shaped stud and the lower one clear crystal and one blue bead. Zagotovlen only 4 such suspension and bend the ends of the wire into a simple loop.
- Attach the lower short suspension, the lower inner loop. From the inner loop earrings (where long is attached below the internal suspension)attachable fixtures. Open loop swanzy tools like ring. Put it on the inner loop from above and close. Similarly, to execute the second earring.
- For manufacturing major parts of the pendant will need a coil of wire of large diameter and ? a coil of small diameter wire.
- In the center of the circle of wire of large diameter placed one large blue bead. Further, on both sides symmetrically strung on: one blue bead, five light blue beads, one blue bead, one crystal, one blue bead, 10 blue beads, one blue bead, one crystal, one blue bead, 10 blue beads, one blue bead, one blue busine. Continue to string on one blue bead, 10 blue beads, one blue bead, one crystal, one blue bead, 10 blue beads, one blue bead, and 5 light blue beads and one blue bead. Make the wire into a ring by stringing on it from two opposite sides one small blue bead. Tighten the wire ends so that two sides were equal segments.
- Through the bottom of a large blue bead stretch ? a coil of small diameter wire. Gently adjust the ends of the wire so that two sides were equal segments.
- On the top side ends of the wire string in: 5 light blue beads, 5 blue beads, 5 blue beads, 5 blue beads, 5 blue beads, 5 blue beads, one crystal and 3 blue beads. At the ends of the wire with pliers put a blocking loop inside. The same pattern strung beads and crystals on the lower ends of small diameter wire.
- Through the side of the large blue crystals threaded circumference of wire of large diameter. Pre-strung in between the beads: 10 light blue beads, 5 blue beads, 5 blue beads, 5 blue beads, 5 blue beads, 5 blue beads, 5 blue beads, 5 blue beads, and 10 light blue beads. Then fasten a piece of wire through the second side bead.
- Gently pull the ends of the wire so that two sides was equal segments.
- On the side cuts down from the blue beads threaded on: 5 light blue beads, 5 blue beads, 5 blue beads and 2 blue beads. The ends of the wire lock internal hinges.
- Of half round wire of small diameter forming a decorative element for hanging the whole structure of the pendant. To do this, take the center wire 3 blue beads. The edges symmetrically placed: 3 blue beads, 3 blue beads, 3 blue and 3 blue beads. The ends of the wire with round nose pliers curl to one side in loops. The beading should lie a bit loose. Neat and bendable wire with beads in the center.
- String beads, fasten a decorative element on two sides from the Central blue beads, capturing the top layer of wire with beads.
- Produce side charms pendant two. The T - shaped stud string one translucent bead and one blue bead. Formed a short suspension. Just harvested 6 of these short suspensions and edges of studs bent with pliers into a simple loop, after cutting off the excess wire. For the formation of long option suspension on the T — shaped stud string one translucent bead and 5 blue beads. Edge curl the pliers into a simple loop.
- At the ends of the upper wire with beads attached to one short and long sling. On the middle tier — one short sling. On the lower inner loop fastened to one short sling.