Side Welt pockets with leaflets with the set ends more typical coat and short coat from mild fabrics, jackets and coats, but maybe less to ativate and jackets.
The processing circuit indicating the details of the cut is shown in figure:
Designations on the scheme:
from the main fabric:
A-before;
B - leaf;
In - the valance;
from the lining fabric:
D - the lining of the pocket;
D - part of the lining of the pocket;
of cushioning material:
E - dolevik;
W - strip leaves.
Configuration details of the cut required for the processing node and n. n. they are presented in the table:
The part name is Sketch the Direction of the warp threads of the main fabric Before
Parallel to cut the side below the top side of the loop
Leaf
Along of the part (fabrics with a NAP, directional pattern, color variation - both in the front)
The valance
Along of the part (fabrics with a NAP, directional pattern, color variation - both in the front)
From lining fabric 1 piece of lining pockets
Deep pockets
Part 2 lining pockets
Deep pockets
Of adhesive material Dolevik
Along details
Strip the leaves
Along details
Processing flow chart indicating the order of execution of srocc caught in the cross-section shown in figure: 
The processing sequence of the pocket is represented in instructional technology map: № p/p the Name of technologically indivisible operation THAT Sketch
1. To identify the location of the pocket on the front With the front side mold 4 lines (the distance between longitudinal lines is equal to the width of the leaves in finished form, between transverse - to the length of the pocket)
2. Stick dolevik to the front With reverse side in the location of the pocket is symmetrical about intended lines
3. To duplicate a sheet an adhesive strip on the reverse side with length 1 cm behind the middle of the leaves
4. To press the leaves Folding in half lengthwise right side out
5.To identify the width of the leaves in finished form At the duplicated part on the front side of the fold
6.To pritchet part of the lining of a pocket to a piece of paper Laying the lining face-to deprotonirovannoi of the leaves, equalizing sections, primativa at the target on a piece of line
7. To pricecat the second part of the lining of the valance pocket to the Folding parts, right sides inside, equalizing sections, sh.sh. 1 cm
8. To press the seam protecive lining of the pocket to the skirt To the side lining of the pocket
9. To pricecat the piece with the pocket lining to the front Putting the details of leaflets on the front side of the front, bend the leaves to the outlet side, equalizing the stitching on the lining with the near to a longitudinal side of the planned line, with a symmetrical output side sections of the leaflets for the transverse the intended line, primativa in the line of protecive lining to the leaf, starting and ending strictly at the level of the transverse lines
10. To pricecat the valance with podklady pockets to the front Putting the valance face on the front side of the front, with sunset at 1 cm beyond the second longitudinal intended line, with symmetricds exit the sides of the valance over the transverse the intended line, primativa sh.sh. 1 cm, beginning and ending strictly on the level of the transverse lines
11. To check the quality of previous operations Lines from the dolevik must be parallel, must begin and end at the same level, the distance between them = the width of the leaves in finished form
12.To cut the pocket in the Middle between the lines, not reaching the transverse lines of 3 cm, cutting Napoli before reaching the thread line 1.5 mm
13. Remove the valance, lining pocket and the ends of the leaves on snanny side of the front Straightening corners
14. Sweep seam primaqiune leaves and valances to the front Slanting or straight stitches, straightening uneven seam, sh.sh. 5 mm, spreading allowances of primaqiune valance to the front in the direction of the front
15. Pritority the entrance to the pocket From the side of the dolevik, by bending the allowances of the side seams of the lining, putting the corners of the cut between the leaflets and pocket lining
16. To baste the piece on the front Parallel to the bend leaves at a distance of 5-7 mm from the edge, watching the parallelism of the ends of the leaves
17. Sew the lining pocket sh. sh. 1 cm, by bending before starting and ending triple back lines, nastraivat the basis of the area of the cut on the ends of the leaves and the valance
18. Remove the thread a temporary assignment with pocket Cutting using 3 cm by removing a peg
19. Priotity pocket on the front side through protohellenic
20. To test the quality of the machining of the pocket Piece the same width, the ends are parallel and correctly executed WTO
