You will need:
6 bars with a length of 150 mm for the frame base;
approximately 35 bars with a length of 400 mm for racks;
23 rod with a length of 125 mm for additional racks;
2 rod with a diameter of 8 mm and a length of 300 mm (for seat back);
thin rods to weave the base and walls;
2 small cloves.
Base
Prepare the crosspiece of the six bars. Appetite the crosspiece of the way, "twisting"to the base diameter was equal to 80 mm. the surface should be slightly concave. Bars crosses divide one on the third row of weaving. Then make three rows with a way to "rope". Sharpen one end of each of the twenty three rods for the uprights (their number should be odd) and insert them into the base.
Bend the strut and tie their ends so that the convex side of the base was outside. Appetite stand, making five rows with a way to "rope".
Sharpen and insert twenty-three additional Stoics (as well as in weaving a large basket). Weave wall height of 25 mm by the method of "direct weaving". Ensure that the "basket" has expanded. To do this, pull back on each rack. Then again, do five rows a way to "rope". Trim the protruding ends of the additional racks, squeeze the pliers, the main stand at a distance of 6 mm from the woven edge of the wall, make the edge of "the rod" of three or four rods and finish weaving the edge of the "track" to the ends of the rods went inside the "basket". Before weave edge you need to make sure that the walls of the baskets have the same height around the entire circumference.
Back
Flip the woven part of the seat (the basket) upside down. Focus you have left unused bars for racks. Paste them along the walls stands the "basket". Two thick rod position from the edges, forming a sort of "armrests" seat (figure 1). To do this, first determine the size of the back. (Stand back, try not to locate too close to each other. The width of the backrest can be anything; its strength is achieved by bending.) In determining the size of the back you can use small pieces of thin vines, which then need to remove, and in their place insert with the awl thicker struts (see figure 1). Tips stands for "arms" cut off obliquely.
Put the chair back to him. Go around a thin rod around to the left of the thick strut to make one long and one short end. These two bars appetite all stand back a way of "twisting" (figure 2). Leave the short end and continue straight weave one long end. Rounding a thick stand every second or third time, make one additional coil around these stands (figure 3). When connecting the new bars in their place the protruding ends of the outer side of the back. Try to weave so that the upper half of the backrest was leaned back. Continue to braid for as long as the back height reaches 75 mm (figure 4). In the middle region of the back should be higher than the edges. To do this, continue weaving in the following manner: before reaching a thick stand around neighboring thin the rack and whipping back, also reaching a thick stand. The next row of weaving must be even shorter, etc. until you weave around two or three stands in the middle of the back. This whole process repeat as many times as needed.
When the chair will be high enough, make one row of weaving right to left and then one number method "sophisticated twist". This method is very simple (figure 6); only each time the output of the rod out you need to stretch it under the previous row.
Edge
The edge of the chair differs from the usual edge "the rod" of the three bars because it's not on the circumference and ends at the opposite stand. Turn the chair back facing you. Tighten all strut with the pliers at a distance of 6 mm from the last row of weaving. Prepare two racks with a length of 200 mm and one rack with a length of 350 mm. Rods with a length of 200 mm, insert the next to the left of a thick bar — one in front and the other to the side (use it with the awl). A rod with a length of 350 mm, the resulting go around all three stands (figure 7). Bend the front added the rack down so that it passed between the two ends of the kinked rod. You have three rods for the netting edge "the rod". First, the left rod from the front and miss the second behind the third bar. Fold the first straight line (added) rack. Now bend the next two racks, you have got three pairs of bars facing out (figure 8). Continuing the braiding, take the fifth, counting from the right, the rod and go around them mesognathy the first rack front and a second behind. Bend the straight rack, etc. until, until there is one video stand.
Take the fifth, counting from the right, the rod and measure the distance to them right a thick stand of a back seat. Mark this distance, clenching his rod in this place with pliers. Then trim the rod, stepping back to 40 mm further away from the marked locations (figure 9). Insert the cut end of the rod near a thick stand. Bend the last direct rack and curve it around a thick pillar, as shown in figure 10. Secure the last coils of nails, then trim the thick a-pillar to a-level edges (figure 11).
Similarly, you can weave a child seat, but this will require a thicker and durable material. The spider should be collected from the eight bars with a length of 275-300 mm.
If you want to start making furniture large, it is necessary to acquire sufficient experience weave small things.
Hat for dolls
You will need:
10 thin rods with a length of 350 mm;
20 thin rods of length 175 mm for racks;
40 thin rods with a length of 100 mm for racks edge;
thin rods for weaving;
material for finishing (tape, etc.).
All operations run in exactly the same way as in the weaving of a boater, but the crown of the hat draw method "curl" to the size of 40x50 mm and the way the "rope" only do two rows. Add twenty pillars and three proplatit some way "twisting"and one a number of way to "rope". Then proceed to weave the sides of the crown. The depth of the crown is only 18 mm.
Field hats do as when weaving boater. Make three or four rows way to "rope". Insert one rod for netting edges next to each bar. Edge make double bars (racks).
Trim the ends of the rods and proceed to finish the hat.